NEED CONTACT for Paul Conrad
3 posters
Page 1 of 1
NEED CONTACT for Paul Conrad
Hi all mustang fans.
I have recently bought Pauls mustang GT 05 (photo attached) - imported here, to the Czech Republic. I would really need to ask him few questions about the mustang mods and the software. It was very difficult to find the cars previous owner.
Do any of you have his email address? Or any hint, how can I contact him? His nickname was "musiccitygt" on this forum, but it doesn exist anymore. He should also be the owner of the "wildhorsesclub.net" domain name.
Thank you all!!!
Jan Diblik
I have recently bought Pauls mustang GT 05 (photo attached) - imported here, to the Czech Republic. I would really need to ask him few questions about the mustang mods and the software. It was very difficult to find the cars previous owner.
Do any of you have his email address? Or any hint, how can I contact him? His nickname was "musiccitygt" on this forum, but it doesn exist anymore. He should also be the owner of the "wildhorsesclub.net" domain name.
Thank you all!!!
Jan Diblik
invertart- Number of posts : 5
Age : 39
Re: NEED CONTACT for Paul Conrad
Hi Jan, T.J. here. Paul has been gone and not had a lot of contact with the club for about 4 years now. I Don't remember everything but I can tell you what I do know about the car as last I had seen it. I know the tune was done by Running with the Devil tuning out of Atlanta, GA. and that he had the NO2 setup programmed to run between 3000 up to 5000 RPMs when activated. Unfortunatley I don't remember the tuning software that was used on it. As far as the rest of the car, he had just done the basic bolt ons to it, as well as a Line Lock system for the beaks. If you any specific questions, please let me know and i can help as best as i can.
As far as trying to get a hold of Paul himself, I don't have a crrent number or e-mail adress for him.
As far as trying to get a hold of Paul himself, I don't have a crrent number or e-mail adress for him.
Krutch21- Small Block 351W
- Number of posts : 469
Age : 45
My Name: : T.J
My Ride/Rides: : 04 Mystichrome Cobra
Re: NEED CONTACT for Paul Conrad
Hi T.J.
Thank you for fast answer. I have all the documentation from the Stang. The first tune was from Devils and the second for NO2 is from Brenspeed.
The problem is that few sensors are worn off (both lambdas, mass air flow sensor and one cam shaft sensor), and if we replace them by new parts the main unit doesn recognize them.
So maybe we will have to revert the main unit to original software, but I dont have it. In the SCT is only the Diablo and Brenspeed tune....
So I wanted to ask paul if he doesnt have the original software somewhere...
Thank you and have a nice day.
Jan
Thank you for fast answer. I have all the documentation from the Stang. The first tune was from Devils and the second for NO2 is from Brenspeed.
The problem is that few sensors are worn off (both lambdas, mass air flow sensor and one cam shaft sensor), and if we replace them by new parts the main unit doesn recognize them.
So maybe we will have to revert the main unit to original software, but I dont have it. In the SCT is only the Diablo and Brenspeed tune....
So I wanted to ask paul if he doesnt have the original software somewhere...
Thank you and have a nice day.
Jan
invertart- Number of posts : 5
Age : 39
Re: NEED CONTACT for Paul Conrad
That is strange. There should always be a back-up factory tune in an SCT tuner. Why it is not on the tuner I do not know. Wha you can also do to get the tune file is go to SCT' website, send them a mail with the situation and they should be able to e-mail you a copy of a Factory tune for your year mustang. That may be your best bet to fix your situation.
Krutch21- Small Block 351W
- Number of posts : 469
Age : 45
My Name: : T.J
My Ride/Rides: : 04 Mystichrome Cobra
Re: NEED CONTACT for Paul Conrad
So I got it wrong before, the problem is somwhere else. The PCM unit is stuck so it throws error whenever you try to reflash it with other software. The guys in Bosch here didnt manage how to repair it, so it has to be sent to the US and restored at the dealers... we dont have any official dealer of US Ford here in Europe.
invertart- Number of posts : 5
Age : 39
Re: NEED CONTACT for Paul Conrad
Where are you stationed at. Might be able to help you out with some info.
steves04cobra- Small Block 289
- Number of posts : 123
Age : 43
My Name: : Steve
My Ride/Rides: : 2004, Cobra, moron
Mods: : K&N CAI, 2.93" pully, Dyno tunned, Spec stage 3 clutch, B&M shifter, Flowmaster exuast,
Re: NEED CONTACT for Paul Conrad
Hi, I'm in Czech Republic, Europe
invertart- Number of posts : 5
Age : 39
Re: NEED CONTACT for Paul Conrad
Ok im stationed in Bamberg GM. I'll see if anybody knows where to get this done at.
steves04cobra- Small Block 289
- Number of posts : 123
Age : 43
My Name: : Steve
My Ride/Rides: : 2004, Cobra, moron
Mods: : K&N CAI, 2.93" pully, Dyno tunned, Spec stage 3 clutch, B&M shifter, Flowmaster exuast,
Re: NEED CONTACT for Paul Conrad
Hi, thank you very much, but we've already sent it to Detroit to guys who did this before with firends mustang pcm with the same problem and it works perfectly since.
Thanks again, I'll let you hnow how it goes.
Thanks again, I'll let you hnow how it goes.
invertart- Number of posts : 5
Age : 39
Re: NEED CONTACT for Paul Conrad
Alright man good luck
steves04cobra- Small Block 289
- Number of posts : 123
Age : 43
My Name: : Steve
My Ride/Rides: : 2004, Cobra, moron
Mods: : K&N CAI, 2.93" pully, Dyno tunned, Spec stage 3 clutch, B&M shifter, Flowmaster exuast,
Similar topics
» Congrats to Paul and Andrea
» City Council Attempting to Limit Speedway Hours
» Paul! i need some help
» Happy Birthday Paul.
» paul's secret uncovered !!!
» City Council Attempting to Limit Speedway Hours
» Paul! i need some help
» Happy Birthday Paul.
» paul's secret uncovered !!!
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum
|
|